CH Flightstick Pro Y axis range

[plokkum]

Hey guys,

I own a CH set, including the Flightstick, Throttle and Pedals.
Everything seems to work fine except for the flightstick.

When I push the stick all the way forward, the raw data outputs 0, which is perfect. However, when I pull the stick backwards for just half an inch, the raw data outputs 255 already! So in other words, pulling the stick towards me is about 5 times as sensitive as pushing it forwards, which often results in stalling my airplane ingame due to pulling up too quickly.

Is there anyone who is experiencing the same problem? Or maybe someone who knows a solution? I use CH' tool to calibrate.

[335th_GRAthos]

Well, I presume you post first, search later... anyway here are some extracts from various threads in here that may be of help:


Q: How do I set up my joystick?

A: On the Control Options screen, choose the "Axes" tab on the top of the screen. If you want to assign joystick buttons (or mouse/keyboard buttons/keys), choose the "Keys" tab.
----

Q: The throttle goes to maximum even if my joystick throttle is only at 10-20%

A: Go to Control Options, Select Axes tab.
Select the throttle axis and look at the sliders for 0% Position and 100% Position.
Set for example 0.10 for 0% Position
and 0.90 for 100% Position
(This gives a bit of dead zone at both ends)


Episeis kapios egrapse:
tf_neuro
Member Join Date: Mar 2011
--------------------------------------------------------------------------------
-Select your throttle axis in the settings interface
-At the bottom of the page, you will see 5 sliders (left) and 2 indicators (right)
- Set the 5 sliders as follows, top to bottom:
*slider#1 = 0.02
*slider#2 = 0.00
*slider#3 = 1.00 <= all the way to the right
*slider#4 = 0.00
*slider#5 = 0.02
- Now the indicators on the right should move almost together, except for 2 small dead zones at both ends, to make sure that the game actually goes all the way down to 0% and up to 110% throttle
(to eliminate the dead zones set sliders #1 and #5 to 0.00)



Formula88
Junior Member Join Date: Apr 2011
--------------------------------------------------------------------------------

OK, I got it figured out! I was on the right track but what I failed to realize was that my 1946 was on a fresh install and I hadn't set up my controller for it yet. After I set up my controller in 1946 I went into its config file and sure enough the proper values were now in there. I simply copied and pasted from the 1946 config to the CoD one. Here is what it looks like:

[rts_joystick]
X=0 1 4 9 16 25 36 49 64 81 100 0
Y=0 1 4 9 16 25 36 49 64 81 100 0
Z=0 10 20 30 40 50 60 70 80 90 100
RZ=0 10 20 30 40 50 60 70 80 90 100 0
FF=0
U=0 10 20 30 40 50 60 70 80 90 100 0
V=0 10 20 30 40 50 60 70 80 90 100 0
1X=0 1 6 10 15 22 33 44 58 72 100 0
1Y=0 1 6 10 16 23 31 43 56 73 100 0
1Z=0 100 100 100 100 100 100 100 100 100 100 0
1RX=0 100 100 100 100 100 100 100 100 100 100 0
1RY=0 100 100 100 100 100 100 100 100 100 100 0
1RZ=0 1 4 8 13 21 28 39 52 69 100 0
1U=0 100 100 100 100 100 100 100 100 100 100 0
1V=0 100 100 100 100 100 100 100 100 100 100 0

This, everyone, I have confirmed to work! You need the 1X values for it to work not the X values, the axes with the 1 infront are what windows uses to set the joystick sensitivity.




Hope it helps,

Happy Flying!

~S~