Can't load Saitek X52 pro 64bit profile

[335th_GRAthos]

Not quite sure I understand but I can explain how it works with my Saitek and maybe you can find out what you need:

The Profile Editor is used to allocate keystrokes or keystroke combinations to your joysticks.
At the top dropdown menu it always shows which joystick you are currently setting up (X45, throttle, rudders etc etc).
Always select the Joystick picture (in order to be sure you are allocating keystrokes to the joystick you want to use and not to a different joystick tan the one you have) and then proceed to the buttons table.

The Saitek joysticks you have are shown (if properly installed) as small icons on the bottom right of your taskbar. One for each joystick.
In my case, I have four icons: One for X45, one for throttle quadrant, one for second throttle quadrant, one for rudders. The icons are black.
I go with the mouse on top of the icon I want (e.g. X45) I right-click with he mouse and I see the list of available profiles I have created with the profiler.
I select the profile I have preparedfor my X45. The profile loads and the black icon get a green background colour to indicate that a profile is loaded.
I right-click upon the second throttle quadrant icon and I select the profile I have prepared for the throttle quadrant. This icon now also gets a green background.

I have loded the two profile I need (one for the X45 and one for the second throttle quadrant).

IF I load a profile on the wrong joystick e.g. I load the X45 profile on the Throttle quadrant, I get the error message you mentioned.


I hope it helps.

~S~

[Dano]

Originally Posted by cheesehawk

You might need to completely redo your profiles, I did when I switched from 32-bit SST to 64-bit SST.

Would be my guess too, incompatiabilities between the two versions I suspect. Sucks

[darky1]

Try this one it works fine for me as its my set up from my machine also a 64bit machine
http://driverscollection.com/?H=X52%20Pro&By=Saitek

[salmo]

Thanks everyone. I have the latest drivers. Yes, I'm creating a new profile from scratch. Yes, I'm using the 64bit X52 pro profiler. Yes, I've uninstalled & reinstalled devices. The "Salmo.pr0 does not contain a profile for this device. The device has not been profiled" persists. Googling the problem suggests that I could be making a X52 profile, and that the X52 & the X52 pro profiles are incompatible with each other. This is not the case, I definitely have the X52 PRO profiler. Also, I've dowloaded ready-made X52 PRO profiles & they fail to load & give the same error.

[335th_GRAthos]

Did you ensure this???

Originally Posted by 335th_GRAthos

...At the top dropdown menu it always shows which joystick you are currently setting up (X45, throttle, rudders etc etc).
Always select the Joystick picture (in order to be sure you are allocating keystrokes to the joystick you want to use and not to a different joystick tan the one you have) and then proceed to the buttons table.

~S~

[salmo]

No top-dop-down menu I'm afraid. I'm using the 64bit profiler from Saitek. The file name is called Saitek_X52Pro_Flight_Controller_SD6_64 downloaded from ftp://ftp.saitek.com/pub/software/fu..._2_7_64bit.exe

[335th_GRAthos]

Originally Posted by salmo

No top-dop-down menu I'm afraid. I'm using the 64bit profiler from Saitek. The file name is called Saitek_X52Pro_Flight_Controller_SD6_64 downloaded from ftp://ftp.saitek.com/pub/software/fu..._2_7_64bit.exe

Hold on a sec,

The file Saitek_X52Pro_Flight_Controller_SD6_64 is the drivers for your joystick so that it is properly recognised as a joystick in Win7
Similarly, I have the drivers Saitek_X45_Flight_Controller_SD6_64_DRIVERS.exe & Saitek_Pro_Flight_Rudder_Pedals_SD6_64.exe installed.

What about the Profiler SW???
What I am using is the SST_Software_64_6_6_6_9.exe (229Mb)
This is the one I use for all my Saitek joysticks (although I do not have a X52Pro to give a direct opinion on your HW).

I see there is also a 19Mb Saitek_X52Pro_Flight_Controller_SD6_64_Software_.e xe
Have you installed this?

The ftp has a nice list of drivers... ftp://ftp.saitek.com/pub/software/full/


I can not be sure but I think you should check whether the SST_Software_64_6_6_6_9.exe (229Mb) is compatible with your X52Pro and if so, download this one and install it.

my 2cents...


~S~

[salmo]

My bad, I meant Smart_Technology_7_0_2_7_64bit file for the profiler.

[335th_GRAthos]

OK, then,

you should check whether the SST_Software_64_6_6_6_9.exe (229Mb) is compatible with your X52Pro and if so, download this one and install it.


~S~

[zl2bmh]

Hello All.

Why use SST at all, can smeone tell me that. I have CLoD and a X52Pro controller, and just configured the game from the 'keys and axis'. No need for SST. I am very interested to know why SST is used.
regards,
zl2bmh jim.