Fulqrum Publishing Home   |   Register   |   Today Posts   |   Members   |   UserCP   |   Calendar   |   Search   |   FAQ

Go Back   Official Fulqrum Publishing forum > Fulqrum Publishing > IL-2 Sturmovik: Cliffs of Dover > Technical threads

Technical threads All discussions about technical issues

Reply
 
Thread Tools Display Modes
  #1  
Old 01-24-2013, 07:46 PM
bolox bolox is offline
Approved Member
 
Join Date: May 2008
Posts: 351
Default

Quote:
Originally Posted by lorenzoj View Post
. I think my best route would be to attach my old rudder pedals to a new Flight stick / throttle set if that's do-able.
You have Elite pedals , correct? (and yes they are rather nice)
AFAIK they will only connect to specific Thrustmaster HOTAS, eg Cougar.

The wiring of the pot may also be problematic if you try to attach to a Bodnar board (or similar) as it uses a 2 wire system, rather than a 3 wire 'voltage divider' circuit used by these.

This cougar wiring pic shows the pins used.
Reply With Quote
  #2  
Old 01-24-2013, 08:12 PM
lorenzoj lorenzoj is offline
Approved Member
 
Join Date: Dec 2012
Posts: 59
Default

My set goes back further then that. Here is the link to my Craigslist add with some good photos. Big, solid and heavy best describes the pedals. Just rudder axis though, no toe brake function.

http://boston.craigslist.org/sob/vgm/3552777941.html
Reply With Quote
  #3  
Old 02-02-2013, 10:50 PM
Sokol1's Avatar
Sokol1 Sokol1 is offline
Approved Member
 
Join Date: Oct 2007
Posts: 727
Default

Quote:
Originally Posted by bolox View Post
You have Elite pedals , correct? (and yes they are rather nice)
AFAIK they will only connect to specific Thrustmaster HOTAS, eg Cougar.

The wiring of the pot may also be problematic if you try to attach to a Bodnar board (or similar) as it uses a 2 wire system, rather than a 3 wire 'voltage divider' circuit used by these.
The pedal linked in Craiglist is the Tm RCS, prior of Tm Elite.

I dont find problem to wire one in modern USB controller, just is not "PnP".
As noted is need use 3 wires instead 2, and I did it using original cable:



The cable external shield net is now GND wire.
The pot in picture is original Tm - later replaced by a HALL Sensor.

In this small box fit the new USB controller - a DIY Mjoy8.



To interface the USB box with computer use a ordinary USB A/B printer cable.

A similar approach can be done with BU0836 or similar.

BTW - In the original form this pedal have only one axis, no brakes axis.

Sokol1

Last edited by Sokol1; 02-02-2013 at 11:13 PM.
Reply With Quote
  #4  
Old 02-03-2013, 03:37 AM
lorenzoj lorenzoj is offline
Approved Member
 
Join Date: Dec 2012
Posts: 59
Default

Excellent photos and instruction. Very clear. Yes that is very much like my old pedals. I am good with tools but no experience with this so How do you then set up pedals in the programs like IL-2 and MSFS ? Thanks.
Reply With Quote
  #5  
Old 02-11-2013, 02:37 PM
Sokol1's Avatar
Sokol1 Sokol1 is offline
Approved Member
 
Join Date: Oct 2007
Posts: 727
Default

Lorezonj

Just like another controller (joystick, pedal, throttle...)

In game GUI select the desired function, ie rudder, them move the pedal. Done.

Modern games recognize various controllers up to 16 (Windows limit) - only IL-2 1946 is limited to four.

Sokol1
Reply With Quote
  #6  
Old 02-14-2013, 01:35 PM
lorenzoj lorenzoj is offline
Approved Member
 
Join Date: Dec 2012
Posts: 59
Default

I went ahead and ordered a usb - gameport convertor from Amazon for about half of what I could get the BU0836 for, which seemed like overkill for just getting a single axis rudder pedal to work. Reviews were pretty good keeping in mind that some people would have trouble operating a wooden toothpick correctly.

One guy returned a flight control stick and throttle set cause he couldn't figure out where to plug the cable from the throttle... "my computer doesn't have a matching socket.." Gee I wonder what this socket on the back of the stick base is for ?

Remember if all else fails RTFM

http://www.amazon.com/gp/product/B00...ls_o00_s00_i00

Edit: The adaptor arrived from Amazon and has four mode positions on the switch, each referring to a different combination of axis and buttons. My computer recognized I had another controller plugged in after I connected the pedals via the adaptor. But no matter what I tried I could not get a good calibration and the rudder was always over to the left when "neutral" and no better then at center when fully pressed right. I will try it with my old complete Thrustmaster FCS System when I get a chance just to see how that functions.

Last edited by lorenzoj; 02-17-2013 at 10:06 PM.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 09:06 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © 2007 Fulqrum Publishing. All rights reserved.