AMD 7970HD 3Gb and CoD

[Flanker35M]

S!

I used the drivers that came upon launch of the card.

[Jugdriver]

Did you notice a change with the new 12.3/8.95 drivers? Reason I ask is that our general system specs are not that far apart but my benchmark in the Black Death track is a lot slower (average) than yours. The card is certainly an improvement over my 5870, but I am at a loss as to why my average in the black death track is so far off of yours. I just got the card installed last night so I obviously need to tweak it a bit, I am just trying to get my head around it.

JD
AKA_MattE

[Flanker35M]

S!

My CCC settings below, try them I will also set my conf.ini for comparison.

CCC

Anti-Aliasing: Use application settings, Morphological OFF, Filter at Standard
Anisotropic Filtering: Application settings
Tessellation: AMD Optimized
Catalyst AI: Performance, Surface Opti OFF
Vertical Refresh: On unless app specifies
AA Mode: Performance
OpenGL: Triple buffer Off


And the conf.ini regarding 3D..

[BOB]
EpilepsyFilter=0

[window]
DepthBits=24
StencilBits=8
DrawIfNotFocused=1
SaveAspect=0
Render=D3D10_0
width=1920
height=1080
posLeft=0
posTop=0
ColourBits=32
FullScreen=1
ChangeScreenRes=1
Frequency=60
StereoMode=0



[core]
RandSeed=0
TexQual=2
TexFlags.PolygonStipple=0
Shadows=1
SpecularLight=2
DiffuseLight=2
DynamicalLights=1
MeshDetail=2
LandShading=2
LandDetails=2
Sky=3
Forest=2
VisibilityDistance=3
LandGeom=2
DrawCollisions=1
Water=-1
Effects=1
EffFlags.Light=1
EffFlags.SpriteRender=0
Grass=3
CordEffect=1
UseFog=0
UseLandCube=1
UseLandConnectedObject=1
LinearObjectManager=1
Roads=1
Sun=1
Clouds=1
EffFlags.LightSpritesProj=1
ShadowMapSize=4
TexFlags.AsyncLoad=1
TexFlags.ShowTexture=0
SimpleMesh.SWTransform=0
SimpleMesh.QuadTreeClip=1
SimpleMesh.InstancingHW=1
EffFlags.LightContextSprites=1
CloudsFlags.Detailed=1
TexFlags.CreateHDR=1
Decals=2
EffFlags.SWLight=0
TexFlags.CockpitOnePass=0
MegaTexture=0
TexFlags.Reflection=0
RenderTargetQual=3
MSAA=0
MeshStatics=3
MeshStaticsDetail=1
SimpleMesh.QTNoCompose=0
MeshFirstLod=0
MeshShowLod=0
SpawnHumans=0
TexFlags.SSAO=0
TexFlags.VSync=1
TexFlags.FastTransparency=1

[Jugdriver]

Thanks Flanker, I will work on it tonight after work.

Appreciate the help.

JD
AKA_MattE

[Flanker35M]

S!

I hope those settings help or give an idea where to look at Just not fiddling so much now as the patch is around the corner so we will see how that changes the situation

[Jugdriver]

Flanker could you answer another question for me, looking in GPU-Z when flying COD what is your GPU load?

Thanks

JD
AKA_MattE

[Flanker35M]

S!

I think I posted it earlier in the thread, something around 40% or so average. So not very much.