|
IL-2 Sturmovik The famous combat flight simulator. |
|
Thread Tools | Display Modes |
#11
|
||||
|
||||
its already enabled in the 4.08m version so if you can see it in skin dl servers.
__________________
71st Eagle Squadron www.anon6.com - Blogger on DCS Series 71st Mastiff's You-Tube " any failure you meet is never a defeat; merely a set up for a greater come back " Asus||i7x5930k||16gb3200||GTX10808gb||ATX1200Corsa ir||CBTitanium7.1||Win10x64||TrackIr4Pro/ir||gladiator pro mkII||siatekpedals||X52Throttle||G15Keyboard/RazerMouse|| 32"LCD||2x7" lilliputs,1x9inc |
#12
|
||||
|
||||
Everything installed fine. MAT files where copied, but nothing shows up ingame Just default markings.
|
#13
|
||||
|
||||
Thanks for your work on this..........question....is it possible to change the markings on the chevrolet medical truck to a German vershion?...I have a limited fuel mission, where the medical truck is timed to meet my ariving, often damaged aircraft....That star on the truck must go
|
#14
|
||||
|
||||
This is my problem I think. I go into windows, right-click on the cache or netcache folder, I uncheck the box wich says 'read-only' and I click 'apply'. The next time I right-click on the folder, the read-only box is checked again. What am I doing wrong?
Can anyone help please? Mat markings still not showing in the game. |
#15
|
|||
|
|||
Hi folks,
For those having problem with removing read only for folders here's a step-by step instructions. 1. click on windows "start" menu 2. click on "Run" 3. in the box where it says "open" type "cmd" (without the quotes) 4. when the dos box appears type the following: cd c:\Program Files\Ubisoft\IL-2 Sturmovik 1946\PaintSchemes in the above example you should substitute the correct path to your games folder if it is not installed on C drive in the default folder path as per the above example. Make sure to add the PaintSchemes bit to the end. and hit the "enter/return" key on your keyboard 5. When the path displayed changes to the above type the following without the quotes "attrib -r Regiments" and hit the enter/return key 6. then type "attrib -r Cache" again without the quotes and hit the enter/return key That's it. I downloaded the new installer and ran in here on a works PC and then ran MAT Manager, made a few markings changes and then exited and I never had the Read Only problem so it would appear that there's nothing wrong with the files zipped in the installer being zipped as read only. Please try the above. Also please remember to add the ClearCache=0 command to the [game] section of your conf.ini else you will not see any MAT Manager markings. The Netcache folder isn't used by MAT Manager only the Regiments and Cache folders it is these folders that must not be read only. Regards Aces I'm afraid that vehicle markings cannot be changed as the skins with them on are hard-coded into the game. |
#16
|
|||
|
|||
@ 3./JG51_Rudel:
The link to Filefront doesn´t work no more. 1. Is there a change to upload all in one installer for mat manager v2.36? 2. Would it be ok if I´d put up the files on our squads website? Best regards, Emil |
#17
|
||||
|
||||
Yes. (Big or small and all 1936 - 1945 variants [yes, from 1936 too])
|
#18
|
|||
|
|||
You would be mad not to use it.
Standard markings look toy like after you get used IL2MAT. |
#19
|
||||
|
||||
Having trouble finding this all inclusive patch...also installing earlier versions of same....any tips ...have changed config file & changed fb to il2exe.with no results!
|
|
|