#21
|
|||
|
|||
thank you very much
|
#22
|
|||
|
|||
Quote:
|
#23
|
|||
|
|||
Quote:
The leading and trailing zeros are kind of like stoppers, without these the config and controller wouldnt know where the axis begins and where it ends. All of the other axis are for various sliders on the stick so the number of these may vary depending on what model stick you have. |
#24
|
|||
|
|||
I thought the zeros were deadzones (in IL-2 at least). Thanks for the effort, Formula88.
|
#25
|
|||
|
|||
Finally had a chance to test this properly. Relevant section of my 1C Softclub conf.ini is:
[rts_joystick] FF=0 X=0 1 4 9 16 25 36 49 64 81 100 0 Y=0 1 4 9 16 25 36 49 64 81 100 0 Z=0 10 20 30 40 50 60 70 80 90 100 RZ=0 10 20 30 40 50 60 70 80 90 100 0 U=0 10 20 30 40 50 60 70 80 90 100 0 V=0 10 20 30 40 50 60 70 80 90 100 0 1X=0 1 6 10 15 22 33 44 58 72 100 0 1Y=0 1 6 10 16 23 31 43 56 73 100 0 1Z=0 100 100 100 100 100 100 100 100 100 100 0 1RX=0 100 100 100 100 100 100 100 100 100 100 0 1RY=0 100 100 100 100 100 100 100 100 100 100 0 1RZ=0 1 4 8 13 21 28 39 52 69 100 0 1U=0 100 100 100 100 100 100 100 100 100 100 0 1V=0 100 100 100 100 100 100 100 100 100 100 0 There is no difference in control sensitivity when I switch between everything at 1 and everything at 100 (or anything more sensible in-between) for both X, Y and 1X, 1Y. Not sure what's going on with my config since other users have reported this to be working. Any ideas? |
#26
|
|||
|
|||
Not working for me either
Hi I have the x52 pro and find it way to sensitive as well the in game sensitivity sliders seem to have no effect cuting and pasting the config.ini seems to have no effect. In searching for an answer I came across a program that Oleg made IL2 Joy control.
http://www.mission4today.com/index.p...etails&id=1021 Will this work for COD? Thanks Gordo62 |
#27
|
|||
|
|||
I have two questions for you guys:
First, do we have a consensus whether the old IL2 [Joystick_RTS] functions in CoD conf.ini? Second, as far as ALL the trim axes go, does the dead zone at 0% and at 100% refer to the center (50% of travel) of the axes or the way the are shown in the control panel ?(0% all the way to the left and 100% all the way to the right) I would ask the same thing about the rudders but those are usually self centered so I am assuming the center is 0% in rudders. |
#28
|
|||
|
|||
Well, in my *.ini file there is only one entry under [rts_joystick] and that's FF=1.
Nothing else and I feel that my controls are hugely sensitive and there is no way of tuning them from a menu in game! Feels like something is amiss here ?!
__________________
Gigabyte MA790FX5-UDP Phenom II X4 955 BE 3,4 GHz 8 GB DDR3 1333 Raid 0 Array 2x Radeon XFX HD6870 1GB |
#29
|
|||
|
|||
Quote:
|
#30
|
|||
|
|||
Quote:
If this is in fact the case (correct me if I am wrong) then I recommend that those who find the lines they have edited have not had an effect attempt to try editing lines referring to another controller (ie if you have edited lines with "1" at the start, then try instead editing lines that have no number there). |
|
|