Flight Stick Axis Sensitivity?
 

Having poroblems controlling Stall and Spin on many of the stock a/c ( Cyborg X flightstick). I know that the flightstick response can be tailored in the menus and the user manual suggests alternative settings but wondered if the majority of you experienced iL2 flyers were using the same settings for the axis response for all a/c or do you adjust the Axis sensitivity for each and every a/c that you pilot?

The LA5 for example is fine with the default settings but, switch to a Spitfire or a P51-D for example) and the slightest deviation of the stick results in stalling or spinning. I do not want to disable 'stall and spins'.

At the moment, having to alter stick response each time for different aircraft would be a pain, and I expect most of us just find a compromise that works for us. Whet suits you may not be what suits others, but as you say the manual suggests an alternative setup if you are having problems:
Note that though this reduces sensitivity near the stick centre position, it will increase it at the extremes - if it didn't, you wouldn't get full control surface movement.

As I understand it, Team daidolos were looking at including multiple user-defined control setups in a future patch - enabling different sensitivity curves for different aircraft.

The P-51 is a bit of a beast for a beginner - it is a little easier to handle with a lower fuel load. With Spitfires, force feedback helps if you have it - you feel the shake at the onset of stall. Otherwise, you have to rely on visual signs, and experience. If you are really struggling, try something with easier handling - a Hurricane perhaps, or one of the earlier Japanese fighters - they are mostly fairly forgiving.

Cheers Andy, tried a variety of settings and eventually resolved the 'instabilty'. I will modify the Elevator axis profile for each of the aircraft, the Aileron axis profile seems fine left at one set of values.

Check to make sure the joystick values in config.ini have 0 at the end, ie:

0 0 5 10 17 25 33 43 54 71 100 0

Should be 12 figures all together, first 0 is for deadzone, last 0 is for filtering. Game seems to clip the last one occasionally, causes erratic input for me. I set config.ini as read-only after I've made any changes.

hey guys!
hey evangeluse!!!!
as i play now for about one week this game, i have the same problems like SEE setting up the sensitivities of the axis. i have set the roll and the pitch axis up to your recommendation AndyJwest, but i dont know where i can change the yaw axis as it doesnt appear in my menu!???can somebody tell me where i can find it!? and what is the filter under the axis meaning?thx for all information.

From the manual (manual.pdf in your IL-2 folder):
AS for why the rudder axis settings don't show, I don't know. How are you controlling the rudder? Pedals? Twisty joystick?

IL-2 will only assign sensitivity settings to one controller - so if you are using pedals then your rudder cannot be adjusted in the in-game window. If you are using a twisty stick then it may help if you "bind" the twist-axis in the HOTAS section of Controls. This is done in the same way as direct button assignments - open the window opposite the required axis and then move the stick in the required direction. The axis designation will appear in the window - job done.

The easiest solution however, is not to use the in-game sensitivity mapper at all! Set it all to 100 and then download IL-2 Joy Control from www.mission4today.com
This user-made utility will help you to set curves for every axis that you can command, dependent on how many sliders or rotaries you have. It has an easy-to-understand GUI and several features that are a big improvement on the in-game methods.

Brando

hey andyjwest!thx for the tips.
but my biggest problem is that i dont know the meaning of the ten bars for each of the axis. the first is for the deadzone i assume, but i dont know what the other 9 are for.
if i set for the pitchaxis the last bar on 100 i have big problems not to stall. if i have set them all on 50 or 60, i can turn well, but not thight enough, and everyone is outturning me online.

Hi David, not ready to go on line yet but I have set my elevator axis down on the last range to around 75 while I get to grips with IL 1946. Everything I have read suggests that the last set of axis data should always be left at 100 but I can't get on with that setting on the 'elevator axis' at the moment. Ailerons I find can be left more or less at 100 and this has made the flight on the twitchier a/c more stable and predictable. When I have sussed the flight physics I will join on line. I can't keep up with other identical a/c at the moment and have posted a question in hope someone can explain why.........:(

I think full real settings would be only 100 percent sensitivity since adjust joystick responses is a way to solve the vices of some airplane. May settings could allow only a deadband for old joys, however new joys is much more precise and not need such deaband or filtering stuffs.

I always fly 100% as a way to obtain higher immersion. To me adjust joy config is some kind of cheat, cause you are changing your plane natural responses to obtain a easy way to flight.